The suitability of nettle plants for the production of pulp and paper was thoroughly examined, with special consideration given to the plant’s chemical compositions, morphological analysis, and kraft pulping qualities. The mean values of cell wall thickness, fiber length, lumen width, runkel ratio, and nettle plant diameter were found to be 7.4 μm, 55 mm, 4.9 μm, 2.4 and 16.9 μm, respectively. Although nettle plant fibers have a stronger cell wall, their physical properties are comparable to another biomass. The chemical composition investigation found that the contents of nettle plants were 64.8 weight percent holocellulose, 38.7 weight percent alpha-cellulose, 16.8 weight percent lignin, and 5.8 weight percent ash. Additionally, 8.4 weight percent were discovered in the 1% alkaline extractives of nettle leaves. The kraft pulping process of nettle plants needed a low chemical charge and lower boiling time when compared to a number of other non-wood raw materials utilized in the papermaking process. Despite these circumstances, kraft-pulped nettle plants yielded a high-yield bleachable grade pulp. Kraft pulp produced from bleached nettle plants had strength properties that were comparable to those of other biomass for pulp and papermaking materials. Overall, this present research show that nettle plants, which have morphological and chemical characteristics comparable to those of traditional papermaking materials, have a bright future as a source of pulp and paper.
| Published in | Journal of Biomaterials (Volume 8, Issue 1) |
| DOI | 10.11648/j.jb.20240801.11 |
| Page(s) | 1-14 |
| Creative Commons |
This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited. |
| Copyright |
Copyright © The Author(s), 2024. Published by Science Publishing Group |
Nettle Plant (Steam), Kraft Pulping, Fiber Resources, Fiber Morphology, Chemical Compositions
| [1] | Abd El-Sayed, E. S., El-Sakhawy, M., & El-Sakhawy, M. A. M. (2020). Non-wood fibers as raw material for pulp and paper industry. Nordic Pulp and Paper Research Journal, 35(2), 215–230. https://doi.org/10.1515/npprj-2019-0064 |
| [2] | Azeez M. Pulping of Non-Woody Biomass. Pulp and Paper Processing. 2018, 24, 7, 1213-1232. https://www.intechopen.com/books/advanced-biometric-technologies/liveness-detection-in-biometrics |
| [3] | Adnan, N. A., Sapuan, S. M., & Ilyas, R. A. (2021). Pulp and paper production : A review. Advanced Bio- and Mineral Based Natural Fibre Composites (SBMC2021), January, 9–13. |
| [4] | Akgül, M., Erdönmez, I., Çİçekler, M., & Tutuş, A. (2018). The Investigations on Pulp and Paper Production with Modified Kraft Pulping Method from Canola (Brassica napus L.) Stalks Kanola Saplarından (Brassica napus L.) Modifiye Kraft Yöntemi ile Kağıt Hamuru ve Kağıt Üretimi Üzerine Araştırmalar. 18(3), 357–365. https://doi.org/10.17475/kastorman.499091 |
| [5] | Alam, M., Rikta, S. Y., Bahauddin, K. M., Hasnine, T., & Kamal, A. K. I. (2018). Production of eco-friendly handmade paper from wastepaper and other local biomass material Research Paper Production of eco-friendly handmade paper from wastepaper and other local biomass material. Academia Journal of Environmental Science, 6(7), 147–155. https://doi.org/10.15413/ajes.2018.0128 |
| [6] | Alila, S., Besbes, I., Rei, M., Mutjé, P., & Boufi, S. (2013). Non-woody plants as raw materials for production of microfibrillated cellulose (MFC): A comparative study. Industrial Crops & Products, 41, 250–259. https://doi.org/10.1016/j.indcrop.2012.04.028 |
| [7] | Andersone, I., Andersons, B., & Avramidis, G. (2012). Handbook of Wood Chemistry and Wood Composites. In Handbook of Wood Chemistry and Wood Composites (Issue December 2020). https://doi.org/10.1201/b12487 |
| [8] | Anthony, W. S. (2005). Development of machines to separate fiber and shive from seed flax straw. Applied Engineering in Agriculture, 21(6), 1057–1063. |
| [9] | Aqsha, A., Tijani, M. M., & Mahinpey, N. (n.d.). Catalytic pyrolysis of straw biomasses (wheat, flax, oat and barley straw) and the comparison of their product yields. 190, 1007–1015. https://doi.org/10.2495/EQ140942 |
| [10] | Bajpai, P., Mishra, S. P., Mishra, O. P., Kumar, S., Bajpai, P. K., & Singh, S. (n. d.). Biochemical pulping of wheat straw. 3(8), 3–6. |
| [11] | Benvenuti, A. J., Drecksler, S. R., Gupta, S., Menezes, A. A., & Gupta, S. Sen. (2020). Design of Anaerobic Digestion Systems for Closed Loop Space Biomanufacturing. 1–12. |
| [12] | Brännvall, E. (2009). Overview of pulp and paper processes. Pulping Chemistry and Technology, 1–11. https://doi.org/10.1515/9783110213423 |
| [13] | Chai, X. S., Luo, Q., & Zhu, J. Y. (2000). Institute of Paper Science and Technology A tanta, Georgia A Simple and Practical Pulp Kappa Test Method. 873. |
| [14] | Danielewicz, D., & Surma-ślusarska, B. (2010). Processing of Industrial Hemp into Papermaking Pulps Intended for Bleaching. 18(6), 110–115. |
| [15] | Daud, Z., Awang, H., Sari, A., Kassim, M., Zainuri, M., Hatta, M., & Aripin, A. M. (2014). Cocoa Pod Husk and Corn Stalk : Alternative Paper Fibres Study on Chemical Characterization and Morphological Structures. 911, 331–335. https://doi.org/10.4028/www.scientific.net/AMR.911.331 |
| [16] | Description, P., & Streams, W. (2018). Pulp and Paper Processing. Pulp and Paper Processing. https://doi.org/10.5772/intechopen.68843 |
| [17] | Díez, D., Urueña, A., Piñero, R., Barrio, A., & Tamminen, T. (2020). and Lignin Content in Di ff erent Types of Biomasses by Thermogravimetric Analysis and Pseudocomponent Kinetic Model. Processes, 8(1048), 1–21. |
| [18] | Enayati, A. A., Hamzeh, Y., Mirshokraie, S. A., & Molaii, M. (2009). Papermaking potential of canola stalks. BioResources, 4(1), 245–256. https://doi.org/10.15376/biores.4.1.245-256 |
| [19] | Engida, G. (2017), Kraft Pulping of Wheat Straw. Pulp and paper processing.aau repository. http://etd.aau.edu.et/handle/123456789/27 |
| [20] | G. A. Tadele. (2016). Separation and Characterization of Ethiopian Origin Nettle Fiber. International Journal of Engineering Research and Technology (IJERT), 5(3), 259–262. http://www.ijert.org |
| [21] | Gülsoy, S. K., & Şimşir, S. (2018). Kemijski sastav, morfologija vlakana i sulfatni postupak proizvodnje celuloze od stabljika paprati (Pteridium aquilinum (L.) Ksuhn). Drvna Industrija, 69(1), 23–33. https://doi.org/10.5552/drind.2018.1725 |
| [22] | Haggith, M., Kinsella, S., Baffoni, S., Anderson, P., Ford, J., Leithe, R., Neyroumande, E., Murtha, N., & Tinhout, B. (2018). The State of the Global Paper Production. 1–90. https://environmentalpaper.org/wp-content/uploads/2018/04/StateOfTheGlobalPaperIndustry2018_FullReport-Final-1.pdf |
| [23] | Haile, A., Gebino, G., Tesfaye, T., Mengie, W., Ayele, M., Abuhay, A., & Yilie, D. (2023). Utilization of non-wood biomass for pulp manufacturing in paper industry: case of Ethiopia. Biomass Conversion and Biorefinery, 13(9), 7441–7459. https://doi.org/10.1007/s13399-021-01424-x |
| [24] | Haile, A., Gelebo, G. G., Tesfaye, T., Mengie, W., Mebrate, M. A., Abuhay, A., & Limeneh, D. Y. (2021). Pulp and paper mill wastes: utilizations and prospects for high value-added biomaterials. Bioresources and Bioprocessing, 8(1). https://doi.org/10.1186/s40643-021-00385-3 |
| [25] | Halvarsson, S. (2010). Manufacture of straw mdf and fibreboards. http://www.diva-portal.org/smash/get/diva2:324791/FULLTEXT02 |
| [26] | Hunsigi, G. (1989). Agricultural fibres for paper pulp. Outlook on Agriculture, 18(3), 96–103. https://doi.org/10.1177/003072708901800301 |
| [27] | Hurter W. Nonwood Plant Fiber Uses in Papermaking. TAPPI 1997 Nonwood Fibers Short Course Notes. 2001, 1–4. https://www.paperonweb.com/Articles/plant fiberuses. |
| [28] | Idris, F. E. A., & Mohammed, N. A. (2016). Physical and Strength Properties of Paper Manufactured from Straw of Different Sudanese Sorghum Varieties. September. 98, 102–113. https://doi.org/10.1016/j.apenergy.2012.03.002 |
| [29] | Jahan, M. S., Gunter, B. G., & Rahman, A. F. M. A. (2011). Substituting Wood with Nonwood Fibers in Papermaking: A Win-Win Solution for Bangladesh. SSRN Electronic Journal, 4(4). https://doi.org/10.2139/ssrn.1322292 |
| [30] | Javier-Astete, R., Jimenez-Davalos, J., & Zolla, G. (2021). Determination of hemicellulose, cellulose, holocellulose and lignin content using FTIR in Calycophyllum spruceanum (Benth.) K. Schum. And Guazuma crinita Lam. PLoS ONE, 16(10 October), 1–12. https://doi.org/10.1371/journal.pone.0256559 |
| [31] | Kuparinen, K., Vakkilainen, E., & Tynjälä, T. (2019). Biomass-based carbon capture and utilization in kraft pulp mills. Mitigation and Adaptation Strategies for Global Change, 24(7), 1213–1230. https://doi.org/10.1007/s11027-018-9833-9 |
| [32] | Laurijssen, J., Faaij, A., & Worrell, E. (2012). Energy conversion strategies in the European paper industry – A case study in three countries. Applied Energy, 98, 102–113. https://doi.org/10.1016/j.apenergy.2012.03.001 |
| [33] | Leponiemi, A. (n.d.). (2011). Fibres and energy from wheat sraw by simple practice. 69(1), 23–33. https://research.aalto.fi/en/publications/fibres-and-energy-from-wheat-straw-by-simple-practice |
| [34] | Li, L., & Lee, H. L. (2011). Hydrogen peroxide bleaching of hardwood kraft pulp with adsorbed birch xylan and its effect on paper properties. May 2015. |
| [35] | Liu, Z., & Wang, H. (2018). Pulping and Papermaking of Non-Wood Fibers. 3–32. https://doi.org/10.5772/intechopen.79017 |
| [36] | M, K. O. L., K, B. J., & Baptist, K. J. (2013). A Review on Pulp Manufacture from Non Wood Plant Materials. 4(3). https://doi.org/10.7763/IJCEA.2013.V4.281 |
| [37] | Marques, G., Rencoret, J., Gutiérrez, A., & Río, J. C. (2010). Evaluation of the Chemical Composition of Different Non-Woody Plant Fibers Used for Pulp and Paper Manufacturing. 93–101. |
| [38] | Mussatto, S. I., Jackson, G., Rocha, D. M., & Roberto, I. (2008). Hydrogen peroxide bleaching of cellulose pulps obtained from brewer’s spent grain Hydrogen peroxide bleaching of cellulose pulps obtained from brewer ’ s spent grain. August. https://doi.org/10.1007/s10570-008-9198-4 |
| [39] | Nyang, M. G., Muumbo, A. M., & Ondieki, C. M. M. (2019). Production of Particle Boards from Sugarcane Bagasse and Euphorbia Sap. International Journal of Composite Materials, 9(1), 1–6. https://doi.org/10.5923/j.cmaterials.20190901.01 |
| [40] | Ogunwusi, A.., & Ibrahim, H. D. (2014). Advances in Pulp and Paper Technology and the Implication for the Paper Industry in Nigeria. Industrial Engineering Letters, 4(10), 3–12. |
| [41] | One, C. C., Two, C., & Three, C. (2019). Production and characterization of pulp from flax straw 2019, 4(11), 5-22. http://www.repository.smuc.edu.et/handle/123456789/3651 |
| [42] | Pahkala, K. A., Paavilainen, L., & Mela, T. GRASS SPECIES AS RAW MATERIAL FOR PULP AND PAPER. 2018, 5, 8, 521-523. https://www.jetir.org/papers/JETIRA006094. |
| [43] | Pego, M. F. F., & Bianchi, M. L. (2022). Physical and Mechanical Properties of Papers Produced From Different Cellulosic Pulps Blending. https://doi.org/10.21203/rs.3.rs-2257060/v1 |
| [44] | Ragauskas A. 2023. PULP CHARACTERIZATION Lignin. Foreste. 24, 5, 68-78. https://doi.org/10.3390/f14050882 |
| [45] | Report, F. and A. (1980). Pulping and paper- making properties of fast- growing plantation wood species. Food and Agriculture Organization of United Nations: Technical Report. |
| [46] | Rodrı, A. (2008). Rice straw pulp obtained by using various methods. 99, 2881–2886. https://doi.org/10.1016/j.biortech.2007.06.003 |
| [47] | Ross, K., & Mazza, G. (2010). Characteristics of Lignin from Flax Shives as Affected by Extraction Conditions. 4035–4050. https://doi.org/10.3390/ijms11104035 |
| [48] | Rousu, P., Rousu, P., & Anttila, J. (2002). Sustainable pulp production from agricultural waste. Resources, Conservation and Recycling, 35(1–2), 85–103. https://doi.org/10.1016/S0921-3449(01)00124-0 |
| [49] | Sadiku, N. A., & Abdukareem, K. A. (2019). Fibre morphological variations of some Nigerian Guinea savannah timber species. Maderas: Ciencia y Tecnologia, 21(2), 239–248. https://doi.org/10.4067/S0718-221X2019005000211 |
| [50] | Salmela, M., Alén, R., & Vu, M. T. H. (2008). Description of kraft cooking and oxygen-alkali delignification of bamboo by pulp and dissolving material analysis. Industrial Crops and Products, 28(1), 47–55. https://doi.org/10.1016/j.indcrop.2008.01.003 |
| [51] | Surma-s, B. (2017). Properties and fibre characterisation of bleached hemp, birch and pine pulps : a comparison. 5173–5186. https://doi.org/10.1007/s10570-017-1476-6 |
| [52] | T211, T. (2002). T211 Ash in wood, pulp, paper and paperboard: combustion at 525°C. TAPPI Standard Test Methods, T211 om-02, 5. https://doi.org/10.1016/j.foodchem.2010.01.034 |
| [53] | TAPPI 2017. (2007). Ash in wood, pulp, paper and paperboard : combustion at 525 ° C. TAPPI-Technical Association of the Pulp and Paper Industry, T 211, 1–7. |
| [54] | Valto, P., Knuutinen, J., & Alén, R. (2012). Overview of analytical procedures for fatty and resin acids in the papermaking process. BioResources, 7(4), 6041–6076. https://doi.org/10.15376/biores.7.4.6041-6076 |
| [55] | Ververis, C., Georghiou, K., Christodoulakis, N., Santas, P., & Santas, R. (2004a). Fiber dimensions, lignin and cellulose content of various plant materials and their suitability for paper production. Industrial Crops and Products, 19(3), 245–254. https://doi.org/10.1016/j.indcrop.2003.10.006 |
| [56] | Ververis, C., Georghiou, K., Christodoulakis, N., Santas, P., & Santas, R. (2004b). Fiber dimensions, lignin and cellulose content of various plant materials and their suitability for paper production. 19, 245–254. https://doi.org/10.1016/j.indcrop.2003.10.006 |
APA Style
Tekleyohanis, T., Woldeyes, B. (2024). Optimizing Kraft Pulping Conditions to Improve Nettle Plant Pulp Quality. Journal of Biomaterials, 8(1), 1-14. https://doi.org/10.11648/j.jb.20240801.11
ACS Style
Tekleyohanis, T.; Woldeyes, B. Optimizing Kraft Pulping Conditions to Improve Nettle Plant Pulp Quality. J. Biomater. 2024, 8(1), 1-14. doi: 10.11648/j.jb.20240801.11
AMA Style
Tekleyohanis T, Woldeyes B. Optimizing Kraft Pulping Conditions to Improve Nettle Plant Pulp Quality. J Biomater. 2024;8(1):1-14. doi: 10.11648/j.jb.20240801.11
Share This Article
Twitter
Linked In
Facebook
Copy
Download@article{10.11648/j.jb.20240801.11,
author = {Tsiye Tekleyohanis and Belay Woldeyes},
title = {Optimizing Kraft Pulping Conditions to Improve Nettle Plant Pulp Quality},
journal = {Journal of Biomaterials},
volume = {8},
number = {1},
pages = {1-14},
doi = {10.11648/j.jb.20240801.11},
url = {https://doi.org/10.11648/j.jb.20240801.11},
eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.jb.20240801.11},
abstract = {The suitability of nettle plants for the production of pulp and paper was thoroughly examined, with special consideration given to the plant’s chemical compositions, morphological analysis, and kraft pulping qualities. The mean values of cell wall thickness, fiber length, lumen width, runkel ratio, and nettle plant diameter were found to be 7.4 μm, 55 mm, 4.9 μm, 2.4 and 16.9 μm, respectively. Although nettle plant fibers have a stronger cell wall, their physical properties are comparable to another biomass. The chemical composition investigation found that the contents of nettle plants were 64.8 weight percent holocellulose, 38.7 weight percent alpha-cellulose, 16.8 weight percent lignin, and 5.8 weight percent ash. Additionally, 8.4 weight percent were discovered in the 1% alkaline extractives of nettle leaves. The kraft pulping process of nettle plants needed a low chemical charge and lower boiling time when compared to a number of other non-wood raw materials utilized in the papermaking process. Despite these circumstances, kraft-pulped nettle plants yielded a high-yield bleachable grade pulp. Kraft pulp produced from bleached nettle plants had strength properties that were comparable to those of other biomass for pulp and papermaking materials. Overall, this present research show that nettle plants, which have morphological and chemical characteristics comparable to those of traditional papermaking materials, have a bright future as a source of pulp and paper.
},
year = {2024}
}
TY - JOUR T1 - Optimizing Kraft Pulping Conditions to Improve Nettle Plant Pulp Quality AU - Tsiye Tekleyohanis AU - Belay Woldeyes Y1 - 2024/03/13 PY - 2024 N1 - https://doi.org/10.11648/j.jb.20240801.11 DO - 10.11648/j.jb.20240801.11 T2 - Journal of Biomaterials JF - Journal of Biomaterials JO - Journal of Biomaterials SP - 1 EP - 14 PB - Science Publishing Group SN - 2640-2629 UR - https://doi.org/10.11648/j.jb.20240801.11 AB - The suitability of nettle plants for the production of pulp and paper was thoroughly examined, with special consideration given to the plant’s chemical compositions, morphological analysis, and kraft pulping qualities. The mean values of cell wall thickness, fiber length, lumen width, runkel ratio, and nettle plant diameter were found to be 7.4 μm, 55 mm, 4.9 μm, 2.4 and 16.9 μm, respectively. Although nettle plant fibers have a stronger cell wall, their physical properties are comparable to another biomass. The chemical composition investigation found that the contents of nettle plants were 64.8 weight percent holocellulose, 38.7 weight percent alpha-cellulose, 16.8 weight percent lignin, and 5.8 weight percent ash. Additionally, 8.4 weight percent were discovered in the 1% alkaline extractives of nettle leaves. The kraft pulping process of nettle plants needed a low chemical charge and lower boiling time when compared to a number of other non-wood raw materials utilized in the papermaking process. Despite these circumstances, kraft-pulped nettle plants yielded a high-yield bleachable grade pulp. Kraft pulp produced from bleached nettle plants had strength properties that were comparable to those of other biomass for pulp and papermaking materials. Overall, this present research show that nettle plants, which have morphological and chemical characteristics comparable to those of traditional papermaking materials, have a bright future as a source of pulp and paper. VL - 8 IS - 1 ER -
Department of Chemical Engineering, Debre Berhan University, Debre Behan, Ethiopia
Information